Super Silicone Seal

94 / 100

Super Silicone Seal has been formulated to protect all roofs against heat and ultraviolet. This product will adhere to Metal, Modified Bitumen, EPDM Rubber, and TPO.

A roller, brush, airless sprayer can be used to apply Super Silicone Seal. When used in conjunction with polyester fleece, Super Silicone Seal can be used as a flashing detail or seam repair.

Any metal roof seam, flashing, or EPDM roof can be repaired with Super Silicone Seal.

Always tape off the area you want to protect from the silicone sealant, if not you will have runs of sealant everywhere. Use a rag to wipe off unwanted spills.

Watch this video made by Flat Roof Doctor on how to apply this Sealant over seams and also painting an EPDM Rubber.

Super Silicone Seal 1
The Roof Sealant

How long does it take for Super Silicone Seal to dry?

The curing time is between 48 – 72 hours

How long after I used Super Silicone Seal can it rain?

Around 2 hours after applying Super Silicone Seal it can rain

Where can I buy Super Silicone Seal?

Super Silicone Seal is only available online at Bergstrom Industries

Here are some specs:

The repair of seams, cracks and flashing

  1. Use a steel wire brush to scrub the surface. (remove dust)
  2. Use masking tape to tape off 21/2″ from either side of seam or crack (optional, but looks clean when done)
  3. Measure and cut the correct length of fleece
  4. Brush 1 thick coat either the Turbo Poly Seal or Super Silicone Seal on both sides of crack or seam
  5. Embed the polyester fleece into the freshly painted coat (make sure there are no wrinkles)
  6. Apply another coat over the fleece making sure the fiber doesn’t show
  7. Remove the masking tape

Picture Instructions on how to make flashing repair:

  1. Start by using masking tape to mark the area where the flashing detail will be done. Clean the surface area with a rag.
Super Silicone Seal for vent flashing
Preparing the surface by taping off where the sealant will be installed

2. Measure and cut to size the polyester fleece.

Measure and cut to size the polyester fleece
Measure and cut to size the polyester fleece to be installed over the sealant

3. Apply the first coat by using a brush over the pipe and roof area.

Apply first coat of Super Silicone Seal over pipe and roof area
Apply the first coat over pipe and roof area

4. Cut tabs into the Super Silicone Fleece about 2 inches long.

Cut tabs about 2 inches deep in the measured fleece
Cut tabs about 2 inches deep in the measured fleece

5. Install Fleece around the pipe with tabs spread around lying flat on the roof.

Install Fleece around pipe with tabs spread around on the roof
Install Fleece around the pipe with tabs spread around on the roof

6. Apply a final coat covering the fleece completely

Apply final coat of Super Silicone Seal covering the fleece completely
Apply a final coat covering the fleece completely

7. Repairing a seam on an EPDM Rubber Roof with Super Silicone Seal. Tape off area to avoid spillover

Repairing a seam on an EPDM Rubber Roof with Super Silicone Seal
Repairing a seam on an EPDM Rubber Roof with Super Silicone Seal

8. Apply a thick coat of covering more than 2 inches either side of EPDM Rubber Seam

Apply a thick coat of Super Silicone Seal covering more than 2 inches either side of EPDM Rubber Seam
Apply a thick coat

9. Install a fleece and then paint a final coat covering the fleece

Install a fleece and then paint a final coat of Super Silicone Seal covering the fleece
Install a fleece and then paint a final coat of Super Silicone Seal covering the fleece

10. Remove the masking tape immediately after completing top coat

Remove the masking tape immediately after completing the coating of Super Silicone Seal
Remove the masking tape immediately after completing the top coating

11. The Sealant will be touch dry after 30 min but need another 24 hours to cure.

The Super Silicone will be touch dry after 30 min but need another 24 hours to cure
It is touch dry after 30 min but need another 24 hours to cure

The benefits using Super Silicone Seal is:

  • That it doesn’t dry out
  • It always will stay flexible
  • No paint or coating is needed to protect it from ultraviolet rays
  • It is white and therefor will keep the surface relatively cool
Please write a review about Super Silicone Seal
If you don’t write then I will be sad

2 thoughts on “Super Silicone Seal”

  1. My situation: The house has a pitched, ribbed, metal roof. A brick chimney, which is framed all around with plywood siding, rises up through the rooftop. Rain water is leaking through the roof where the metal sheets abutt the wooden chimney box (water coming through between the metal and wooden box, where the metal meets the wood). The metal roof is pitched, but the framed wooden chimney box is vertical.
    I plan to apply a sandwiched coating of Super Silicone Seal and fleece fabric along the metal-to-wood joint, around all 4 sides of the chimney box. My concerns:
    1) will Super Silicone Seal adhere to the plywood siding of the chimney box?
    2) will Super Silicone Seal stand up to hot summertime temps of ~ 125*F (4 months per year), and how many years can I reasonably expect the repair to last?
    3) is this the correct way to go at this repair? I had originally planned to use Poly Turbo Seal; however, Henry’s #884 silicone roof sealant has already been applied to the leaking joint and I understand Poly Turbo Seal will not adhere to silicone. So, I plan to apply Super Silicone Seal instead.
    Please advise. I learned of Bergmann Industries while watching Roof Doctor’s excellent YouTube videos. – Thanks

Comments are closed.